>>>IMHO I think that some succinct code is harder to read then more long-winded, e.g complicated IIF() instead of If .. ELse ... Endif, the use of !EOF() instead of Not EOF(), abbrev. of VFP commands, petty savings in typing (esp. as one can use global replace for these expressions later - as I often do to othe3r's code to make it readable), using crap short meaningless var names, bad indentation and, worst of all, momnolithic code with 20-page-long Do while loops with several inside them and nested Ifs to boot.
>>>
>>>Personally speaking, IMHO, I think that I have the neatest, most readable, well laid-out code of anyone's I've ever read, and I take great care to make it so.
>>>
>>>But maybe it's only MY mental map that sees it that way.
>>>
>>Show some small pieces and make sure you have a thick screen in front of you <g>
>Well just the latest bit I'm working on for example. BTW I mean In My Humble Opinion, not "Honest" when I write IMHO
>
>

>LOCAL	ldStartCurr, ldEndCurr, ldStartPrev, ldEndPrev, ;
>	lnPercDiff, lnSchTDiff, lnSchemTot2, lnSchemTot1, ;
>	lnTotCurrPass, lnTotPrevPass, lnNotEPrevMult, lnNotECurrMult
>		
>With Thisform
>  If not .lReportCompiled
>      .lmCompileReport()
>      Select csrStep2
>      Sum Trips2, Trips1, CurrPass, PrevPass;
>	to lnSchemTot2, lnSchemTot1, lnTotCurrPass, lnTotPrevPass  && Used in report calcs
>      lnNotEPrevMult  = lnSchemTot1 / lnTotPrevPass		    && Avge ETM multipliers used on notETM
>      lnNotECurrMult  = lnSchemTot2 / lnTotCurrPass
>      IF  ABS( lnSchemTot1)  > 0 ;
>      AND ABS( lnSchemTot2)  > 0 then
>	  lnOverallPercChg	= lnSchemTot2  /  lnSchemTot1 - 1	    && Used in report calcs
>      EndIf
>      Locate
>      .lmRptNoMults()
>  EndIf
>  ldStartCurr	= .dStartDate1
>  ldEndCurr	= .dEndDate1
>  ldStartPrev	= .dStartDate2
>  ldEndPrev	= .dEndDate2
>  lnPercDiff	= .nPercDiff
>  lnPercDiff	= 1 + lnPercDiff/ 100
>  lnSchTDiff	= .nSchemeTrendDiff
>  lnSchTDiff	= 1 + lnSchTDiff/ 100
>  .Visible	= .F.
>
>  Report Form rptCompTrips PREVIEW
>
>  Select csrMultless
>  Report Form rptNoMults PREVIEW
>  .Visible	= .T.
>EndWith
>

>
>or
>

>Insert into RZSTOP ( RTE_NO,   RTE_LET,   DIRECTN,    NUMBER, ZONE, ;
>      		   STOP,                    COUNTY,                 FLAGS,   SEQNO ) ;
>  VALUES           ( lcRoute,  lcGen,     lcDirectn, 	I,     VAL(.aReorderStops( I, 1)),	;
>	            .aReorderStops( I, 3),	.aReorderStops( I, 6),  lcFlag,   1 )
>
>

>
>Sorry, Naomi but when you post some stuff your indentation and such makes it hard to read it. I know the UT imposes its own tabs on what one's written but I always redo it in the UT window

Hmm, the code is fine as is, though I would use m. everywhere (don't want to start flame war <g>). The methods names, though, not very much explanatory, in my opinion. What does lm before lmCompileReport mean?

As for indentation, I always run my code through Beatify program...